# Wayne Dalton TorqueMaster vs Torsion Springs: Pros and Cons

**By Jennifer Oden** · 2025-09-04

Are Wayne Dalton TorqueMaster springs really a good choice, or should you switch to torsion springs? It’s a question homeowners and installers debate often. TorqueMaster springs have unique advantages - and a few drawbacks - that make them different from standard torsion springs.

In this guide (and video below), we’ll break down the **pros and cons of the TorqueMaster system** so you can decide if it’s the right fit for your garage door.

## Pros of TorqueMaster Springs

-   **Safer enclosed design:** The springs are housed inside a steel tube, reducing risk of injury if one breaks.
-   **Compact size:** Great for low-ceiling garages where space is limited.
-   **DIY-friendly:** Can be wound using a ratchet or even a drill - no need for torsion winding bars.
-   **Similar lifespan:** Lasts about as long as torsion springs (7–10 years or ~10,000 cycles) when properly sized.
-   **Made in the USA:** Built from the same steel quality as torsion springs, not cheap imported parts.

* * *

## Cons of TorqueMaster Springs

-   **Hidden failures:** Since the springs are enclosed, it can be harder to tell when they’ve broken.
-   **More moving parts:** End assemblies have small gears and mechanisms that add complexity and potential failure points.
-   **Cost:** Generally more expensive than torsion springs.
-   **Conversion expense:** Switching from TorqueMaster to torsion requires new hardware and is costly.
-   **Improper sizing issues:** If the wrong size spring is installed, over-winding can shorten its life to 2–5 years instead of 7–10.

* * *

## Watch the Full Video

* * *

## Are TorqueMaster Springs Right for You?

-   If you want **ease and safety** for DIY replacement → TorqueMaster is a solid option.
-   If you prefer a **heavy-duty, simpler system** with fewer moving parts → torsion springs are often better.
-   If you already have TorqueMaster springs, **replacing them like-for-like** is usually the most cost-effective solution.

👉 [Shop Wayne Dalton TorqueMaster Springs Here](https://www.expressgaragedoors.com/products/wayne-dalton-torquemaster-spring "Shop Wayne Dalton TorqueMaster replacement springs")

* * *

## FAQs About TorqueMaster vs. Torsion Springs

**Q: Are TorqueMaster springs safer than torsion springs?**  
A: Yes. TorqueMaster springs are enclosed in a steel tube, so if they break, you’re shielded. Torsion springs are exposed and carry more visible tension.

**Q: Do TorqueMaster springs last as long as torsion springs?**  
A: Yes. Both systems typically last 7–10 years or around 10,000 cycles when properly sized and installed.

**Q: Why do some installers dislike TorqueMaster springs?**  
A: They’re more complex, have extra moving parts, and are harder to diagnose when broken. Many service pros prefer the simplicity of torsion systems.

**Q: Can I convert from TorqueMaster to torsion springs?**  
A: Yes, but it requires a conversion kit, new hardware, and professional installation. It’s more costly than replacing TorqueMaster springs with the same system.

**Q: Are TorqueMaster springs made from cheaper materials?**  
A: No. They’re made in the USA from the same steel as torsion springs. They’re simply thinner and enclosed in a different design.

* * *

## Final Thoughts

Wayne Dalton TorqueMaster springs aren’t junk - they’re a homeowner-friendly, safe, and reliable option. While torsion springs are heavier-duty and simpler, TorqueMaster springs make replacement easier for DIYers and last about the same lifespan.

👉 [Order Wayne Dalton TorqueMaster Springs from Express Garage Doors](https://www.expressgaragedoors.com/products/wayne-dalton-torquemaster-spring "Order Wayne Dalton TorqueMaster springs")

---

> Source: [Express Garage Doors](https://www.expressgaragedoors.com/blogs/news/wayne-dalton-torquemaster-vs-torsion-springs-pros-and-cons)